View RSS Feed

optikalefx

  1. New Product: p5USB Hub

    by , 07-13-2009 at 10:31 AM


    Goce from mp3Car shows the advantages to the p5USB hub
    http://store.mp3car.com/DC_Powered_4..._p/adt-015.htm

    Features include:
    Take voltage from 7-32 volts
    guaranteed 500 mA to each port.
    Each port has it's own self resetting fuse
    Reverse polarity protection
    startup and shutdow controller
    Delayed startup and shutdown (5 min and 25 min)

    http://store.mp3car.com/DC_Powered_4..._p/adt-015.htm

    Updated 09-17-2009 at 03:55 PM by optikalefx

    Categories
    Products and Technology , How To Videos
  2. CNX P2140 ACPI over USB to control

    by , 06-23-2009 at 05:26 PM


    Goce from mp3Car takes us through the steps to use your p2140 to hibernate and wake up from hibernation of your laptop.

    Materials needed:
    -Laptop
    -CNX P2140
    store.mp3car.com/Carnetix_CNX_P2140_185W_DC_DC_Regulator_p/pwr-026.htm
    -PSUmoni
    carnetix.com/support.html
    -Vehicle installation

    Make sure you watch our last video to learn how to wire the p2140 to power your laptop!

    Part 2 coming soon.

    Updated 09-17-2009 at 03:58 PM by optikalefx

    Categories
    Products and Technology , How To Videos
  3. CarNetix P2140 (part 2) - Power your laptop with Goce from mp3Car

    by , 06-15-2009 at 08:57 AM
    Goce from mp3Car will walk you through the steps necessary to power your laptop using unregulated ~6~24 volts with only the p2140 and the wire your laptop power adapter came with.



    -For this project you need the following materials:
    -p2140 and 8pin molex output harness
    -Wire strippers 14-22 gauge
    -Bench battery
    -Multimeter
    -Shrink tubing and heat shrink tubing gun OR electrical tape
    -Solder gun and non leaded solder
    -laptop and its power brick
    -knife or scissors

    To finalize this project you should do a continuity test on the stripped wire to find out which is positive and which is negative. Then you can twist and solder the p2140 output wires to the cut laptop brick wires. Turn it on to test it one more time, and then plug it into your laptop to test.

    Updated 12-07-2009 at 03:00 PM by Heather

    Categories
    How To Videos
  4. CarNetix P2140 - Power your laptop with Goce from mp3Car

    by , 06-09-2009 at 10:32 PM


    Goce from mp3Car will walk you through the steps necessary to power your laptop using only the p2140 and the wire your laptop power adapter came with.

    -For this project you need the following materials:
    -p2140 and 8pin molex output harness
    -Wire strippers 14-22 gauge
    -Bench battery
    -Multimeter
    -Shrink tubing and heat shrink tubing gun OR electrical tape
    -Solder gun and non leaded solder
    -laptop and its power brick
    -knife or scissors

    The basic procedure here is to cut and strip the laptop power brick, while NOT cutting the multi-strand wires right beneath the black plastic. Then soldering the positive wire of the primary output from the p2140 to positive end of the now cut power brick cord. And then the same for the negative.

    In the next video we will show you how to test the polarity using continuity and then actually test turing on the laptop using only the power from the p2140 (through the bench battery of course)

    Updated 09-17-2009 at 04:01 PM by optikalefx

    Categories
    How To Videos