Results 1 to 6 of 6

Thread: Is this an good OBD2 Interface ?

  1. #1
    Newbie Centauri_dk's Avatar
    Join Date
    Jul 2006
    Location
    Denmark
    Posts
    26

    Is this an good OBD2 Interface ?

    Hello I am thinking about ordering this OBD2 Interface
    http://www.centauri.dk/mp3car/obd2-102.pdf
    But can someone tell me if thatís a good choose?
    I need it for my Ford Focus 1.6 from 1999.
    The Interface should support 11 protocols. ISO (ISO9141-2), KWP2000 Fast (ISO14230-4), KWP2000 Slow (ISO14230-4), PWM (SAE J1850), VPWM (SAE J1850), K/L og KK/L.
    CAN-Bus 11Bit/250kBaud (ISO15765-4), CAN-Bus 11Bit/500kBaud (ISO15765-4), CAN-Bus 29Bit/250kBaud (ISO15765-4), CAN-Bus 29Bit/500kBaud (ISO15765-4).
    The price is about 105 $.

  2. #2
    Low Bitrate dLockers's Avatar
    Join Date
    Jul 2007
    Posts
    75
    I have seeen this previously, also would this work with my ford fiesta 2002 mk6?

  3. #3
    VENDOR - OBDPros
    Join Date
    Mar 2006
    Posts
    359
    Not a bad price for a muliprotocol scantool, still our scantool www.obdpros.com supports all the protocol at a much lower price $ 84.99 and supports speeds upto 1.2 Mbits and will also work with all the ELM327 software including PCMScan, OBD 2007 & Scanmaster for ELM

    Thanks
    Paul

  4. #4
    North of the land of Hey Huns
    Auto Apps:loading...

    Join Date
    Jun 2004
    Location
    Westminster, MD
    Posts
    2,144
    Yeah, you'll run into problems finding software for that interface, the obdpros.com interface has alot of software written for the chip it's based off of.

  5. #5
    Newbie Centauri_dk's Avatar
    Join Date
    Jul 2006
    Location
    Denmark
    Posts
    26
    Why should i get problem finding software for that interface ? because the write “Software compatible to most of software for ELM32x Chips from ELM Electronics
    (OBD-DIAG, C.E.S. spezial Edition, Scantool, Digimoto, OBD-ScanMaster, wOBD, Real Scan, Scan-Test, OBD Gauge for Pocket
    PC, OBD2ScanTool)”

    About the price, the OBDPro USB Scantool cost 85$ but since I live in Denmark, the normal shipping cost for he is about 30 $ so the price will be the same. Since my price for the other interface is including shipping to Denmark.

    And my plan is to write my own software over the time, sut to start with its always good to have some other to se how it works and analyzing the protocol.

  6. #6
    North of the land of Hey Huns
    Auto Apps:loading...

    Join Date
    Jun 2004
    Location
    Westminster, MD
    Posts
    2,144
    In that case ignore my previous comment about the software, I missed that line in the datasheet. TBH I've never heard of the AGV4000 chip and oddly can't find any information on it, so I can't really say about the quality.

Similar Threads

  1. The search for a good am/fm antenna thread, all welcome.
    By greatwhite in forum General Hardware Discussion
    Replies: 37
    Last Post: 02-05-2010, 03:09 PM
  2. Pioneer Aux interface.... wiring up ... how?
    By Kenny in forum General Hardware Discussion
    Replies: 6
    Last Post: 06-27-2009, 05:56 PM
  3. I2C (not SMBus) SW interface for M10k?
    By rando in forum Software & Software Development
    Replies: 20
    Last Post: 09-14-2004, 01:59 PM
  4. Guidance picking a good HU please?
    By slushieken in forum General MP3Car Discussion
    Replies: 11
    Last Post: 09-13-2004, 02:28 PM
  5. A few questions about an interface
    By naevity in forum Software & Software Development
    Replies: 1
    Last Post: 10-03-2002, 09:31 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •