Results 1 to 7 of 7

Thread: Lilliput 701 in 2004 Santa Fe dash

  1. #1
    Variable Bitrate Spawn12336's Avatar
    Join Date
    Nov 2005
    Location
    Toronto, ON
    Posts
    256

    Lilliput 701 in 2004 Santa Fe dash

    I wasn't going to do this but when I found a deal on it, I couldn't pass it up. These things are usually 300+, I got mine for 175 shipped and taxes in! And it was new!




    As of this weekend, I will finally have a dual monitor setup in the centre console. The new monitor is a Lilliput 701 VGA touchscreen monitor. I have already redesigned my skin to run on 2 monitors. The first thing I noticed is the resolution. I can't get over the difference, night and day just doesn't cover it. I also have to get used to actually using the touch feature instead of the phone. So far it's pretty freaking cool. The standard double din monitor on the bottom is a Pioneer AVH-P6800DVD.

    The advice I need is, I have to block off the vents in the centre console as the screen is sitting where they used to be. What is the best way to do this? I just don't want to stuff the vents with something and worry that it might melt/burn (worst case) when the heat is on in the winter.
    "the universe has a way of balancing itself"

    http://i15.photobucket.com/albums/a3.../Webbanner.jpg

  2. #2
    Variable Bitrate Spawn12336's Avatar
    Join Date
    Nov 2005
    Location
    Toronto, ON
    Posts
    256
    Talked to one of my team members for some advice on small glassing, and threw on an old punisher t-shirt.

    A little stretching, apply resin, wait 1 hour, throw on 2 layers of mat, wait another hour, watch Miami ink while you are waiting, and Voila! I'll trim it tomorrow after it fully cures and start with the bondohair, and bondo.




    "the universe has a way of balancing itself"

    http://i15.photobucket.com/albums/a3.../Webbanner.jpg

  3. #3
    Variable Bitrate Spawn12336's Avatar
    Join Date
    Nov 2005
    Location
    Toronto, ON
    Posts
    256
    Trimmed everything off and gave the edges a quick sand. I had to go drop off something so I figured a fantastic time for a fit and function test. Here's the shots.




    The touchscreen placement is perfectly in reach, and it doesn't sit above the steering wheel.
    "the universe has a way of balancing itself"

    http://i15.photobucket.com/albums/a3.../Webbanner.jpg

  4. #4
    Variable Bitrate Spawn12336's Avatar
    Join Date
    Nov 2005
    Location
    Toronto, ON
    Posts
    256
    Okay, after some reinforced evercoat Plus 1 filler, sanding with 60, some more reinforced filler, more sanding with 60, filling the top with resin to prevent it pulling way from the plastic (apparently I didn't soak the t-shirt enough), a layer of normal evercoat Plus 1 filler, sanding with 60, then sanding with 100, then the "milkshake", sanding with 100, then finishing off with 400, I was ready to paint the piece tonight....

    Until I got to the paint box and realized that I didn't have any! :-\

    So 1 more day with no paint, but it's basically finished. Perfectly functional, placement is working well. install to be completed tomorrow night after I get the boxes and stuff back from the body shop.


    "the universe has a way of balancing itself"

    http://i15.photobucket.com/albums/a3.../Webbanner.jpg

  5. #5
    Low Bitrate
    Join Date
    Nov 2006
    Location
    Gloucestershire, UK
    Posts
    70
    Lush! I want to see the finished product!

  6. #6
    Newbie
    Join Date
    May 2007
    Posts
    1
    how did you block the vents? i might have to do something similar if i make up my mind to do it, :P

  7. #7
    Variable Bitrate Spawn12336's Avatar
    Join Date
    Nov 2005
    Location
    Toronto, ON
    Posts
    256
    Here's a shot from PASMAG from the show this weekend. I haven't had the chance to take my own shots yet. They should be this weekend. And I used expanding foam insulation to block the vents, worked like a charm.

    "the universe has a way of balancing itself"

    http://i15.photobucket.com/albums/a3.../Webbanner.jpg

Similar Threads

  1. My Fiat Stilo 99% complete (Lilliput in Dash)
    By antofa007 in forum Show off your project
    Replies: 37
    Last Post: 06-03-2010, 12:42 PM
  2. FS: Lilliput 701 w/ DIN housing
    By dynamok in forum Classified Archive
    Replies: 2
    Last Post: 11-23-2006, 12:34 AM
  3. Lilliput Pull Out In Dash Conversion
    By Rundell in forum LCD/Display
    Replies: 1
    Last Post: 05-17-2004, 06:58 PM
  4. Help !!, Lilliput In Dash Convert gone wrong
    By markie in forum LCD/Display
    Replies: 3
    Last Post: 04-27-2004, 04:35 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •