Announcement

Collapse
No announcement yet.

Help on Girder/Frodo file!!

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Help on Girder/Frodo file!!

    So I have Frodoplayer all setup for the past 2 weeks (great software BTW Thanks Frodo )
    I decided to add Girder to frodo and use the supplied .gml file.

    What I am trying to do is use frodo to control my HU (volume, preset, source,etc.). I have the IR codes from my Alpine HU already.

    Well I have Girder working as well with those codes but I can't seem to tie in the frodo commands with the IR codes.

    I tried searching through several pages on Frodo and Girder but no luck to my question specfically. Can anybody help?? Thanks guys in advance
    Just getting started...
    Alpine CDA-7995, Toshiba 5205-S503, Lilliput 7" Touchscreen

  • #2
    bump for any suggestions....or any links?
    Just getting started...
    Alpine CDA-7995, Toshiba 5205-S503, Lilliput 7" Touchscreen

    Comment


    • #3
      Did you add "Send Message" plugin in Girder?
      2004 Matrix XR A7N8X-VM/400 AMD XP-M 2500+, DS-ATX
      89 Supra Turbo P3 [email protected]/Abit BE6 II, Alpine M-BUS Car2PC.
      Y2K Accord Dell GX150
      RoadRunner is the best FE PERIOD
      EmoRebellion is a SCAMMER

      Comment


      • #4
        Yes I did.
        Just getting started...
        Alpine CDA-7995, Toshiba 5205-S503, Lilliput 7" Touchscreen

        Comment


        • #5
          AFAIK you cant control anything using FP .

          The file frodo published for girder is to have FP controled by a remote or other device, not to control the device.
          Ikea Case. Epia M10000.M1-ATX. 512 Mb. 2,5" 80 GB HDD. 7" Lilliput. BU-303 GPS. Sony Joystick.
          Status -->
          Lilliput Installed (not indash yet..)
          BraveCar 2.5

          Comment


          • #6
            Originally posted by Bravellir
            AFAIK you cant control anything using FP .

            The file frodo published for girder is to have FP controled by a remote or other device, not to control the device.
            Damn! So how do I go about going the other way, FP output a remote command?
            Is it even possible in FP?
            Just getting started...
            Alpine CDA-7995, Toshiba 5205-S503, Lilliput 7" Touchscreen

            Comment


            • #7
              Originally posted by elk29n
              Damn! So how do I go about going the other way, FP output a remote command?
              Is it even possible in FP?
              Actually yes, but I haven't had the time to write an example.
              [H]4 Life
              My next generation Front End is right on schedule.
              It will be done sometime in the next generation.
              I'm a lesbian too.
              I am for hire!

              Comment


              • #8
                Oh cool. Thanks Frodo! IF you could help me out I'll try it out and post it up...
                or I could just wait for you to write one
                Just getting started...
                Alpine CDA-7995, Toshiba 5205-S503, Lilliput 7" Touchscreen

                Comment


                • #9
                  Originally posted by frodobaggins
                  Actually yes, but I haven't had the time to write an example.
                  Don't have a clue how that can be done.. Can you explain just a little bit?
                  Ikea Case. Epia M10000.M1-ATX. 512 Mb. 2,5" 80 GB HDD. 7" Lilliput. BU-303 GPS. Sony Joystick.
                  Status -->
                  Lilliput Installed (not indash yet..)
                  BraveCar 2.5

                  Comment


                  • #10
                    whenever you get the chance Froso let me know (please )
                    Just getting started...
                    Alpine CDA-7995, Toshiba 5205-S503, Lilliput 7" Touchscreen

                    Comment

                    Working...
                    X