Page 13 of 16 FirstFirst ... 345678910111213141516 LastLast
Results 121 to 130 of 153

Thread: Combined remote / Qwerty keyboard Girder code.

  1. #121
    Maximum Bitrate
    Join Date
    Dec 2003
    Posts
    481
    Vorex- Can u tell us what you did?

  2. #122
    Newbie frankz's Avatar
    Join Date
    Dec 2004
    Location
    Atlanta
    Posts
    33
    I see he still has over 100 of these available:
    http://digibox.co.uk/

    http://cgi.ebay.co.uk/ws/eBayISAPI.d...tem=5739884065
    http://cgi.ebay.co.uk/ws/eBayISAPI.d...tem=5711584110

    he lists 2. one for 7.99 and one for 9.99.
    the latter comes with an ir receiver.

  3. #123
    Newbie mick-uk's Avatar
    Join Date
    Dec 2004
    Posts
    50

    Exclamation Help Would Be Massively Appreciated

    hello all,

    I've been tryin to get my receiver working with no success.

    I followed the instructions posted in this group, and i still had 1 wire left, a red wire, I tried it anyway and nothing.

    so were the cable splits to join the powersupply, i split it, and all the wires snapped off

    and now I have more colours! .

    anyway, could someone psooibly do me a massive favour...
    tell me what colour wires, relate to what pin number from the on digital IR receiver.

    In my receiver:
    I have 7 Pins.

    1 brown
    2 red Think this is Positive Volts
    3 blue
    4 green Think this is Negative Volts
    5 yellow
    6 pink
    7 white

    So if somebody can do a continuity test, between the Serial Port plug, and the Receiver that would be gr8.

    Or if someone can tell me how I can work it out for my self (user "snmnetwork" managed it) I would be ever so greatful.
    snmnetwork

    many thanks
    mik.

  4. #124
    Newbie mick-uk's Avatar
    Join Date
    Dec 2004
    Posts
    50
    yeahhh I diddit!!!
    and it works without power adaptor!

    if you cut off the power adaptor conenctor, the wiring is as follows:

    Colour Pin number
    browny pink.............2
    yellow.............3
    white.............5
    blue.............7
    dark brown.............8
    orange.............not connected
    red.............not connected
    green.............not connected

    * isolate un connected wires.

    The above wiring works **without** the 12v power adaptor, I've modified 2 units both work without.

    however, should your receiver need power, the red is +12v and green is -12v.

    hope this infomation is of some use to people.

    mick.

  5. #125
    Newbie
    Join Date
    Jan 2005
    Posts
    5
    What version of Girder is required? I have 3.2 and the GML file does not work properly, was it created on a later version?

  6. #126
    Newbie JW™'s Avatar
    Join Date
    Nov 2004
    Location
    Valencia, CA
    Posts
    45
    So is it worth picking one of these up? With the tweaks, do they work well?
    JW™
    Powered By Sarcasm

    Ranger: Just bought all my replacement goodies
    Expy: Kenwood KDC-X579 from the Ranger; unknown speakers/amp & 10" Earthquake sub, that all came with the truck

  7. #127
    Newbie JW™'s Avatar
    Join Date
    Nov 2004
    Location
    Valencia, CA
    Posts
    45
    Nobody? (Waah!! Waaaahhh!!!)
    JW™
    Powered By Sarcasm

    Ranger: Just bought all my replacement goodies
    Expy: Kenwood KDC-X579 from the Ranger; unknown speakers/amp & 10" Earthquake sub, that all came with the truck

  8. #128
    Maximum Bitrate clean customs's Avatar
    Join Date
    Jan 2005
    Location
    Houston
    Posts
    500
    I finally got to test out my remote, but ran into some problems after getting all the way to Girder. I used the wiring diagram to put a female plug on the end using the pdf file created by Nemisis. I tested the remote and port out, and got good results. I didn't have to power it up either. In serial watcher, it shows a different code for each button while I have the button down, but has a different value when I let it go.

    But when I go to girder, and try to set an event, it says every button is the same value. I have played with the serial port settings in Girder, and also changed the code on the remote, but the results have been the same. Is there any specific setting for the remote, like the specific code for the remote, or in the settings part of girder for the serial plugin.
    Thanks for the help, I want this thing to work.

    Another thing, using one of the codes, I believe 200, all the buttons on the remote, including the keyboard and the top buttons worked with the single serial port except for the volume and channel controls.
    Round VIII - [IIIIIIIIII] 30% Have some parts for 300zx Sema car I don't own yet. Will have 10.4" & 7" screen, and more then you can believe. Will add updates to cleancustoms.com, will be sweet. My car is still same, but might change.

  9. #129
    Variable Bitrate
    Join Date
    Mar 2004
    Location
    Maryland/NOVA
    Posts
    432
    has anyone got theirs to work using a serial>usb adapter?

    thanks.
    2001 Acura CL traded for a 2006 Subaru Legacy GT
    7" Lilliput Touchscreen
    NANO-ITX+m1-atx
    512 DDRsodimm
    60g SATA Laptop HD
    4x Apple DVDslot
    digimoto OBDii
    mS GPS
    mini BT keyboard
    relocated HU faceplate

  10. #130
    Newbie
    Join Date
    May 2003
    Location
    Suffolk UK
    Posts
    39
    Quote Originally Posted by acura cl
    has anyone got theirs to work using a serial>usb adapter?

    thanks.
    Yes, its how I use mine.

    Works a treat.
    RV Dynamics Nemesis
    Epia M9000 with 20GB 2.5 HD
    7" TFT LCD VGA Monitor & Touch Screen
    Shutdown controller & DC Regulator (Home Made)
    GPS
    On-Digital Remote
    Road Runner Software

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •