Results 1 to 5 of 5

Thread: Touchscreen Calibration.. How Long?

  1. #1
    Constant Bitrate
    Join Date
    Dec 2003
    Location
    Minnesota
    Posts
    122

    Touchscreen Calibration.. How Long?

    I have a Lilliput Touchscreen, and I have yet to calibrate it. It does have some problems currently with the outsides of the screen to be a little off on the left and right. I have run the 4 point and 25 point tests but have yet to finish them. How many times do you have to touch the flashing circles? I have done it about a 100 times before I give up, it doesn't move to another one. I will post a screen shot of my drawing to show you how far its off, and see if thats a problem.
    http://www.AJQuick.com/ - Fiberglassing Tutorials!
    My Cardomain Page - 1998 Dodge Neon R/T

  2. #2
    Constant Bitrate
    Join Date
    Dec 2003
    Location
    Minnesota
    Posts
    122
    The screen shot is attached. The little dots in the corners are where I calibrated to the very corners of the screen, and they appeared in the middle of that box. On the left side of the screen, the lines drew to the right of the line, and on the right side of the screen they appeared on the left. In the middle they were pretty on, but didn't touch the bottom line...nor the top line.
    Attached Images Attached Images  
    http://www.AJQuick.com/ - Fiberglassing Tutorials!
    My Cardomain Page - 1998 Dodge Neon R/T

  3. #3
    Newbie
    Join Date
    Jan 2004
    Posts
    2
    Hi AJ,

    try to push the dots longer, it will take a sec or two until it moves on. I got my Lilliput yesterday and had the same "problem" until i figured it out. Just leave your finger (or pencil) on the dot
    By the way, does anyone here know if it is normal that the calibration only lasts for a couple of minutes? Could it be a temperature problem (itīs below 0 degrees Cel. here at the moment...)?

    Bye,
    oegie

  4. #4
    Low Bitrate
    Join Date
    Aug 2003
    Location
    Moncks Corner, South Carolina
    Posts
    81
    no they tell you wrong, on mine i wait till it beeps, when it beeps i let off, and THEN it moves to the next one

  5. #5
    Constant Bitrate
    Join Date
    Dec 2003
    Location
    Minnesota
    Posts
    122
    I would have thought to hold it down but didn't have a chance to try it out. Thanks for the help.
    http://www.AJQuick.com/ - Fiberglassing Tutorials!
    My Cardomain Page - 1998 Dodge Neon R/T

Similar Threads

  1. Whats easier? Touchscreen or not to touchscreen?
    By jodathmorr in forum General Hardware Discussion
    Replies: 12
    Last Post: 10-21-2003, 12:22 AM
  2. touchscreen calibration is off
    By ELEmental59437 in forum LCD/Display
    Replies: 2
    Last Post: 05-30-2003, 02:43 PM
  3. never lose focus
    By marsjell in forum Software & Software Development
    Replies: 21
    Last Post: 08-12-2002, 02:18 PM
  4. touchscreen (first post, kinda long)
    By poolguy in forum LCD/Display
    Replies: 1
    Last Post: 11-08-2001, 11:38 AM
  5. serial port shutdown signal
    By moahdib in forum Power Supplies
    Replies: 12
    Last Post: 08-03-2001, 09:52 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •