Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: attn: trustworthy soldering pros

  1. #1
    FLAC aoLhaTer's Avatar
    Join Date
    Mar 2003
    Location
    Rohnert Park, CA
    Posts
    1,122

    attn: trustworthy soldering pros

    say i was to send someone a lilliput lcd and an in dash housing from digitalww and i would like them to mod the lilliput to go inside the housing as shown here
    http://digitalww.com/VGA_Lilliput-to-Indash_HowTo.html

    would anyone be willing? (for compensation of course)

    im just worried about ******* up the soldering job because im not that proficient and my iron is a bit antiquated and im limited to one old broad tip that is really hard to use

  2. #2
    Maximum Bitrate Altimat's Avatar
    Join Date
    Oct 2003
    Location
    WI
    Posts
    764
    I'd love to do it for you.
    Fabricator

  3. #3
    Raw Wave hijinks21's Avatar
    Join Date
    May 2002
    Location
    Albany, NY
    Posts
    1,803
    those don't look like too bad soldering points.. its not that hard if you use flux
    '98 Explorer Sport
    http://mp3car.zcentric.com (down atm)
    AMD 800mhz 192megs RAM 60gig hard drive 9 inch widescreen VGA
    80% done

  4. #4
    Raw Wave
    Join Date
    Jun 2003
    Posts
    1,823
    those don't look like too bad soldering points.. its not that hard if you use flux

    You dont even need additional flux, almost all solder are flux cored.

  5. #5
    Low Bitrate belmontboy's Avatar
    Join Date
    Oct 2003
    Location
    England (South East)
    Posts
    77
    flux capacitor

    ??

  6. #6
    Raw Wave
    Join Date
    Jun 2003
    Posts
    1,823

  7. #7
    LAME :) lopan's Avatar
    Join Date
    Dec 2003
    Location
    Clarksville TN
    Posts
    262
    Quote Originally Posted by hijinks21
    those don't look like too bad soldering points.. its not that hard if you use flux
    Everything looks ok except for that button board.... but still doable...

  8. #8
    Maximum Bitrate sfay93's Avatar
    Join Date
    Feb 2004
    Location
    Omaha, NE
    Posts
    777
    I would just take it to a local shop near you. By the time you pay to ship your screen to and from someone on here and pay them for the work it would be about the same price. Plus you could probably get it back quicker from the shop in town because you wouldn't have to wait for it to get there and back. Just my $.02.

  9. #9
    FLAC aoLhaTer's Avatar
    Join Date
    Mar 2003
    Location
    Rohnert Park, CA
    Posts
    1,122
    what shop?

    instructions on the procedure arent terribly detailed either so it might be difficult

  10. #10
    Maximum Bitrate digitalww's Avatar
    Join Date
    Sep 2002
    Location
    ILLINOIS
    Posts
    883
    I updated the "how to", almost done now, and I think it is detailed now. Take a look and let me know if you have any questions.

    Armen

    Quote Originally Posted by aoLhaTer
    what shop?

    instructions on the procedure arent terribly detailed either so it might be difficult

Page 1 of 2 12 LastLast

Similar Threads

  1. soldering iron
    By Cordell in forum General Hardware Discussion
    Replies: 3
    Last Post: 03-14-2003, 02:52 AM
  2. Can a soldering iron "burn down"
    By izaram in forum Off Topic
    Replies: 10
    Last Post: 05-13-2002, 06:17 PM
  3. Trouble soldering
    By Chris Snyder in forum General Hardware Discussion
    Replies: 1
    Last Post: 08-28-2000, 01:37 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •