Lilliput 7" Cable help needed. (Bad 9pin DIN)

**FireAnt** · 03-22-2005, 02:12 AM

I recieved my new Lilliput Model 629GL-70NP/C/T just last week and the 9 pin DIN connector has gone bad (lost 2-4 wire connections internally, Not pins).

I want to cut it out and splice/solder the wires back together. Can some one with the same cable use an Ohm meter and tell me which pins to connect together. Just keep your 9 pin Din hooked together and test for continuity between the tan connector that hooks to the lilliput and the Vga/ USB connectors on the other end.

Thanks for any help, I really want to use this new toy

This is the monitor

Here is the cable with the problem:

The monitor end plug:

The VGA connector

The USB connector

Please just fill in the blanks: Updated 3/29/05 I think this is it now
Blue Numbers-----Red Numbers(VGA)--Green numbers(USB)--Notes
1--------------------3
2--------------------2
3--------------------1
4 Video2+ ------------N/A --------------N/A
5 Video 1 +-----------N/A --------------N/A
6----------------------------------------3
7 Audio 1 +-----------N/A---------------N/A
8--------------------13
9---------------------14
10 --------------------------------1 ground
11---------------------------------1 ground
12 Power 12V+--------N/A--------------N/A
13 Power 12 V+--------N/A-------------N/A
14---------------------------------------2
Shield-Grounds --------shield------------shield

Thanks for everyones help!

Mike

**DorkVonWaterfal** · 03-22-2005, 02:51 AM

Da**, i have the samme problem...
got my screen last week, and already the plug is bad...
turns the screen almost totally black when it gets the bad connection
but is it the extension cable (the long one) witch is bad, or the plug, or is it the short cable(with the SKS Jack) ???

**DorkVonWaterfal** · 03-22-2005, 03:07 AM

i just wrote the seller i Honkong a mail, hope to get a new cable....

**FireAnt** · 03-22-2005, 07:56 AM

It is my sks side right at the 9 pin that developed the shorts. The seller from HK said he will send me a new cable and seems very nice. I would really just like this one to work now! I can't stand the wait and I've cut it apart and ready to solder it up. Can anyone help!
Thanks,
Mike

**FireAnt** · 03-22-2005, 03:00 PM

Yeah,
I have a meter and will try to fill in the blanks for what I can. I was missing about 4 wires it seamed like and was affraid some were reading wrong because of being shorted out. New screen so I hesitate to guess and accidently place the 5 volt+ usb wire to a RGB input by accident.

Mike

**FireAnt** · 03-22-2005, 07:55 PM

Please just fill in the blanks: Updated 3/22/05 What I came up with on my bad cable

Blue Numbers------Red Numbers ------Green numbers --------Notes
1--------------------3
2--------------------2
3--------------------1
4 Audio + ------------N/A --------------N/A
5 Input Video 1 +-----N/A --------------N/A
6----------------------------------------3
7 Input Video 2 +-----N/A---------------N/A
8--------------------14
9----------------------------------------4?----Could be wrong
10
11
12 Power 12V+--------N/A--------------N/A
13 Power 12 V+--------N/A-------------N/A
14---------------------------------------2
Shield-Grounds --------shield------------shield

If someone will do this i would really appreciate it. Please try to confirm what I have here too.

USB pins 1 & 4 unconfirmed
I think i'm missing one wire going to the vga connector?

Thanks,
Mike

**TruckinMP3** · 03-22-2005, 11:44 PM

This is a good one

I do not have an easy answer.... sorry mate. I have replaced an ps2 connection, I very carefull (like you have already started) mapped out the wires to the connector and tested it with my fingers crossed.

My very real suggestion (cause your stuff is more expesive than the touch pad I was playing with) is to wait for the replacement cable and avoid causing damage to any of your parts.

**FireAnt** · 03-27-2005, 12:27 PM

I've tried hooking up the ones I know and it still does not work.

**TruckinMP3** · 03-27-2005, 01:25 PM

Bummer, will you be able to get a replacement cable?

**FireAnt** · 03-27-2005, 07:10 PM

yep, a new replacement cable is supposed to be on it's way by airmail. 7 to 14 days maybe. The waiting is killing me. I really wanted to get used to the touch screen and see if I could use it with out a physical keyboard in my car. At least I have time to import all of my music cd into i-tunes while waiting. And the Mac Mini looks good on a 100" screen from my sharp lcd projector!

Mike