Search:

Type: Posts; User: nrls2000; Keyword(s):

Looking for on the store?
Page 1 of 4 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    4
    Views
    1,360

    My other machines also have sp1 and work...

    My other machines also have sp1 and work appropriately.

    I also have given up on a solution due to the lack of support for this frontend.

    No hard feelings (I like frodoplayer) but probably will...
  2. Replies
    4
    Views
    1,360

    Good Luck ...

    Good Luck

    http://www.mp3car.com/vbulletin/showthread.php?t=85953

    Lots of views little help
  3. Replies
    6
    Views
    1,073

    Found a thread with the same problem ...

    Found a thread with the same problem

    http://www.mp3car.com/vbulletin/showthread.php?t=39306&highlight=remaining+time

    the solution offered was make sure you are using wmp 9 or 10

    I am, does...
  4. Replies
    6
    Views
    1,073

    elapsed time...

    elapsed time
    http://aycu30.webshots.com/image/3309/2005952272882925882_rs.jpg

    remaining time
    http://aycu12.webshots.com/image/6291/2005984790341194702_rs.jpg
  5. Replies
    6
    Views
    1,073

    I would assume the frontend is supposed to...

    I would assume the frontend is supposed to subtract the elapsed time from the total track time.

    The frontend appears to be subtracting the elapsed time from 24 hours rather than the total track...
  6. Replies
    6
    Views
    1,073

    Thank you for the reply fp version is 1.09...

    Thank you for the reply

    fp version is 1.09 take 3 (1.10 does not work on this pc, but it does on the other machines)

    I am using a skin I modified (problem persists with default skin)

    Sorry...
  7. Replies
    6
    Views
    1,073

    Does anybody know where the frontend gets the...

    Does anybody know where the frontend gets the track information for this calculation?
  8. Replies
    6
    Views
    1,073

    Funky Problem: elapsed\remaining time

    Elapsed time works fine

    Remaining time counts down from 23:59:59 erratically

    The status slide at the bottom of the full screen mode goes directly to the end

    None of my other machines have...
  9. Replies
    1
    Views
    769

    nobody is using this mod?

    nobody is using this mod?
  10. Replies
    1
    Views
    769

    xmd-1000 with usb/optical audio

    Currently using xmd-1000 utilizing line-in analog audio. Considering switching to usb audio in or optical in using
    http://www.powerondude.com/product4.htm

    Has anyone used this with frodoplayer? ...
  11. Replies
    7
    Views
    1,070

    Itronix and datalux toughbooks have an optional...

    Itronix and datalux toughbooks have an optional hdd heater. One place I saw you could order it bundled in for $490 extra. Could not find the heater or hard drive available stand alone.
  12. Look for operating temperatures. Standard...

    Look for operating temperatures.
    Standard desktop drives have an operating temperature down to 40 F. Below this they lose rpm's until they don't spin at all. In my research lock-up occurs at...
  13. What speed is your drive? How big? From what I...

    What speed is your drive? How big?

    From what I have seen it gets pretty costly to get 7200 rpm 300 GB hdd with the bearings you refer to.
  14. Yes, when compared to alternative heating...

    Yes, when compared to alternative heating elements.

    That peltier turned into $22.44 after shipping
  15. Yes. Give me demensions needed, desired...

    Yes.

    Give me demensions needed, desired temperature range, and enviromental clearances.
  16. Those are ideas I considered, however I found to...

    Those are ideas I considered, however I found to purchase heating pads new gets upward of $40 (in order to get the wattage necessary for sufficient heat transfer in less than 3 min.). Peltiers also...
  17. HDD Heater for sub-freezing climates - How much intrest is there?

    Creating a bolt on solution to keep hard drive above 60 degrees F.
    Thermostaticly controlled plate will bolt up to the bottom of most standard
    desktop HDD's. Not an adhesive pad heater.
    ...
  18. Replies
    2
    Views
    697

    nobody?

    nobody?
  19. Replies
    2
    Views
    697

    bump

    bump
  20. Replies
    2
    Views
    697

    5.1 analog out w/dvd playback

    I have a intel p4 board with 5.1 analog onboard audio (digital as well). Mini to RCA routed to four amps (1-fronts, 2-rears, 3-subs, and 4-center).

    From the device's control panel all six...
  21. Replies
    34
    Views
    2,258

    The hard drive uses a 5v rail and a 12 volt...

    The hard drive uses a 5v rail and a 12 volt rail(from the power supply). Enough of a voltage dip on the 12 volt rail would cause the hdd not to spin up properly...among other problems.
  22. Replies
    61
    Views
    11,757

    I am currently changing configuration: ...

    I am currently changing configuration:

    Inverter & PSU under driverseat
    new dash screen facia panel
    addl. monitor in drivers visor
    water cooling amps

    In light of all of that I will be...
  23. Replies
    61
    Views
    11,757

    Thanks just a side note: If your LS is still...

    Thanks
    just a side note:
    If your LS is still under warranty have the tranny checked, mine just went out
    at 54,000 miles with typical recall problems. They refused to do anything for me for two...
  24. Replies
    61
    Views
    11,757

    I finally broke down and replaced the factory...

    I finally broke down and replaced the factory battery. Used two optima yellow tops. Modified the factory location to fit them both plus an isolator.

    Unfortunately I am forced into keeping the...
  25. Replies
    61
    Views
    11,757

    Thanks, I've updated some of the pics of this...

    Thanks,
    I've updated some of the pics of this thread.

    Here is the cardomain link
    http://www.cardomain.com/id/nrls2000
Results 1 to 25 of 89
Page 1 of 4 1 2 3 4