Search:

Type: Posts; User: coreyspeed; Keyword(s):

Looking for on the store?
Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7
    Views
    1,471

    thier are loads of adaptors to take a atx to p8...

    thier are loads of adaptors to take a atx to p8 and p9 connectors

    http://www.pccables.com/00326.htm...
  2. Replies
    2
    Views
    592

    32 bit version

    32 bit version
  3. Replies
    1
    Views
    912

    you will need a lvds controller board which will...

    you will need a lvds controller board which will handle the display and backlight connections. you will alos need a touchscreen controller which will handle the touch it looks like you are going to...
  4. Replies
    10
    Views
    4,324

    the adpator looks like to will do the job, just...

    the adpator looks like to will do the job, just buy a standard fan and use that adaptor
  5. get a mp3 player, you cannot connect usb to aux....

    get a mp3 player, you cannot connect usb to aux. but you can get an mp3 and cable to connect the mp3 player to you audio in on your stero
  6. the colour changing would be due to poor...

    the colour changing would be due to poor connection probably between the cable solder and pin, their are serveral different specifcations to vga maybe try looking that up
  7. Replies
    6
    Views
    1,719

    batch files cannot interacte with mice, because...

    batch files cannot interacte with mice, because it is based on ms-dos which never had a mouse to use only keyboards
  8. Replies
    6
    Views
    4,131

    what is wrong with the board ??

    what is wrong with the board ??
  9. Replies
    23
    Views
    1,744

    i dont think you need a new power supply, i...

    i dont think you need a new power supply, i belive your motherboard is not pulling enough power from your power supply to enable it to boot, try adding a couple of 3.5 hard drives on the power supply...
  10. Replies
    28
    Views
    2,138

    helps if we can see the image

    helps if we can see the image
  11. Replies
    2
    Views
    545

    it would be the case you would need to short out...

    it would be the case you would need to short out the green wire to a black to ensure your psu would power on, not sure what pins but i think the green is pin 14
  12. Replies
    6
    Views
    2,058

    make sure the bubble is anti static other wise...

    make sure the bubble is anti static other wise could cause a few problems, deffentily better off shipping in antistatic bag though
  13. Replies
    6
    Views
    1,074

    we have ghot and ghost cast setup at work, we are...

    we have ghot and ghost cast setup at work, we are using the latest version

    symantec ghost solution suite 2.5

    we can create bootable floopies, USB sticks and CD's from a program included called...
  14. Replies
    10
    Views
    1,550

    get a large air tight container place rice in the...

    get a large air tight container place rice in the bottom of it, place the mother board on some spacers so the rice is not touching the board, then seal the container and place in the airing cupboard...
  15. if you where going to buy connectors and solder...

    if you where going to buy connectors and solder them i would use a standard vga cable and chop the ends of, then remove the freittes and solder the conectors back on
    ...
  16. sorry thier is no board in the vga i just wanted...

    sorry thier is no board in the vga i just wanted the picture of the connector and the other pic their will be no risistors on the connector either, you should need to cut the cable atall. you hould b...
  17. Replies
    24
    Views
    5,513

    the two pins you need to solder to are 1 and 2...

    the two pins you need to solder to are 1 and 2 because these are the switch pics on this motherboard
  18. nope both connectors can be broken down, ...

    nope both connectors can be broken down,
    http://www.fpga4fun.com/images/VGAconnectorPluto.jpg http://www.fpga4fun.com/images/VGAconnector.jpg

    the two images show you the conector that is inside...
  19. yep that product would be fine to use, you can...

    yep that product would be fine to use, you can also get SATA versions if your motherboard supports sata
  20. Replies
    5
    Views
    675

    yes this is pefectally possible you would need to...

    yes this is pefectally possible you would need to know if it was 12v or 5v, by looking at the invertors user manuel you should be able to work that out
  21. are you sure you have wired the m2-atx correctly,...

    are you sure you have wired the m2-atx correctly, it sounds like you have a wired the battery to the ignition line rather than the battery line, it would power up when you switch off the ignition the...
  22. Replies
    5
    Views
    1,000

    gennerally computer compontents are compatilbe...

    gennerally computer compontents are compatilbe with -40c to +65c, we have a big enviromental chamber at work and test our products to these temperatures.
  23. Replies
    2
    Views
    705

    try adding the power switch lead to your setup,...

    try adding the power switch lead to your setup, if this does not work try pluging in a 3.5 inch hard drive, it sounds like their isnt enough load on the 12v line for the power suppy to boot.
  24. Replies
    1
    Views
    879

    any pictures ???

    any pictures ???
  25. Replies
    3
    Views
    843

    it would probably be possible, i would image that...

    it would probably be possible, i would image that laptop webcams use a usb protocal. if you have a flat panel lcd monitor i see no reason why you couldnt modify it to have a webcam.
Results 1 to 25 of 89
Page 1 of 4 1 2 3 4