Search:

Type: Posts; User: RonS; Keyword(s):

Looking for on the store?
Page 1 of 5 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    26
    Views
    5,538

    Really the engine is a couple of cockatiels.. :)

    Really the engine is a couple of cockatiels.. :)
  2. Replies
    26
    Views
    5,538

    This what I have on the bench. Not a very good...

    This what I have on the bench. Not a very good video but it will give you and idea. I have both tach and speed on the same source.
    ...
  3. Thread: Bezel needed

    by RonS
    Replies
    2
    Views
    645

    Ok if I am reading this right the frame will...

    Ok if I am reading this right the frame will replace my case. What I did was take the bezel off and glassed it into the dash. Now I am changing the dash so I need either this frame or a new bezel....
  4. Thread: Bezel needed

    by RonS
    Replies
    2
    Views
    645

    Bezel needed

    Does anyone know where I can get a bezel for a Lilliput EBY701? My eyes are crossing looking at all the searching....

    Thanks
    Ron
  5. Replies
    3
    Views
    1,419

    Yes can we get an example. I found an old...

    Yes can we get an example. I found an old example but am not sure where to put it in the code. And it gets over written if I do anything in configurator.
  6. Replies
    51
    Views
    20,828

    You have a PM.. :)

    You have a PM.. :)
  7. Thread: My Speed Sensor

    by RonS
    Replies
    2
    Views
    1,314

    It is the same as the FB speed sensor except it...

    It is the same as the FB speed sensor except it is built with through hole components. The FB sensor works fine but did not let me adjust the output to what I wanted easily. I use three of these. For...
  8. Thread: My Speed Sensor

    by RonS
    Replies
    2
    Views
    1,314

    My Speed Sensor

    I hope no one minds me posting this. But this is the sensor I put together. The cost is higher but I have the option of adjusting the output to what I want. I also have the ability to fine tune the...
  9. Replies
    27
    Views
    3,845

    Any idea when they will be on the site?

    Any idea when they will be on the site?
  10. Replies
    27
    Views
    3,845

    That is true. I forgot all about that. Thanks

    That is true. I forgot all about that. Thanks
  11. Replies
    27
    Views
    3,845

    Yes how do we buy. And also if I am calculating...

    Yes how do we buy. And also if I am calculating correctly. If I put a 1 meg resistor in. I should get 5 volts out at 6000 rpm. 5 *1000000*.01*10^-6*100 I was just looking at the board and if I take...
  12. Replies
    30
    Views
    4,933

    Don't feel bad. I was about to post how good it...

    Don't feel bad. I was about to post how good it was looking and wondering where to download it. :doh:
  13. I am liking this. The only thing I would like to...

    I am liking this. The only thing I would like to see are 2 servo outputs. I need 2. One for heat control and one for heater/defroster control. But that is just me. Keep up the good work.
  14. Replies
    8
    Views
    896

    The problem I have is with their service...

    The problem I have is with their service department. I waited another week and called and they said they still did not have a drive to replace it with and they did not know when they would have one....
  15. Replies
    27
    Views
    3,845

    You've got mail.. :)

    You've got mail.. :)
  16. Replies
    27
    Views
    3,845

    Now you tell me.. After I have already submitted...

    Now you tell me.. After I have already submitted mine. I could have let you do all the work and I could have been lazy and waited. :) Cool if mine have a problem I can order 2 from you and not...
  17. Replies
    20
    Views
    3,247

    If you do a search in google for freq to voltage...

    If you do a search in google for freq to voltage you will find a few million links. Or do a search for LM2907. That will get you what you want.
  18. Replies
    20
    Views
    3,247

    I have just ordered some boards for freq to...

    I have just ordered some boards for freq to voltage. Only problem is they have not been tested and they won't be here for about 2 weeks. But anyway there are a lot of places you can find out how to...
  19. Thread: Heater Switch

    by RonS
    Replies
    3
    Views
    761

    Sorry I did not reply sooner. But thanks. It...

    Sorry I did not reply sooner. But thanks. It works perfect.

    Ron
  20. Thread: Heater Switch

    by RonS
    Replies
    3
    Views
    761

    Heater Switch

    Ok I have myself confused. I want to set the FB to control my heater blower. So I need to have 3 outputs. I need Low, Med, and High. When I switch to Low I need to have the FB make sure the other two...
  21. Replies
    13
    Views
    1,584

    I am having no problems with mine. I only have...

    I am having no problems with mine. I only have 1gig mem for now and am running tinyxp. I did not know it would work with 4gig. That will make life easier.

    Woops just re-read the above post. Never...
  22. Replies
    8
    Views
    896

    Review Toshiba Hard Drives

    I was not sure where to put this and hope this is the right place. I purchased a 120gig laptop drive for my car pc. It lasted about 30 days. So I sent it back. They received it on the 20th of Nov. It...
  23. Thread: I am the first

    by RonS
    Replies
    3
    Views
    862

    Why of course.. But some people think different ...

    Why of course.. But some people think different :angrymob:
  24. Thread: I am the first

    by RonS
    Replies
    3
    Views
    862

    Looks like I got moved.. :)

    Looks like I got moved.. :)
  25. Thread: I am the first

    by RonS
    Replies
    3
    Views
    862

    I am the first

    I get to be the first to post here.... What an innovation... :lol:
Results 1 to 25 of 105
Page 1 of 5 1 2 3 4