Search:

Type: Posts; User: TxAxZxZ; Keyword(s):

Looking for on the store?
Page 1 of 5 1 2 3 4

Search: Search took 0.05 seconds.

  1. I have the same dock as you and have the same bad...

    I have the same dock as you and have the same bad noise problems. I know it isn't my audio setup because it worked fine when I had the carputer setup, and also worked fine when I had my iPhone setup...
  2. Well the wiring schematic didn't work like I...

    Well the wiring schematic didn't work like I thought. I see where I went wrong. As soon as one of the limit switches is hit, the standard relay coil is energized and I loose power to the ejection...
  3. @ RandallFlagg - I tried to take a picture but it...

    @ RandallFlagg - I tried to take a picture but it just didn't come out good. I have the snap-in clips located on both ends of the a/c controls. I'm wondering if the electric windows wiring harness...
  4. So I was doing a little trial and error the past...

    So I was doing a little trial and error the past few days. I temporarily wired up an auto door-lock actuator to the impulse relay. It worked perfect except for one thing. Door lock actuators do...
  5. I see what you're saying now. I haven't used...

    I see what you're saying now. I haven't used anything because I have the snap-in attachments just below the edge that I cut (I'll take a picture of it to post.
  6. Sorry for the late reply Randal, I kind of got...

    Sorry for the late reply Randal, I kind of got busy here and wasn't able to work on my project or get on here to check my post. The bezel (faceplate is attached to the cradle which is hinged on the...
  7. Larue, I got mine at TigerDirect. Here's the...

    Larue,
    I got mine at TigerDirect. Here's the link to the exact one I got. They are out of stock but Amazon has one here. It's made for the GT2 7.0 but I'm sure it would work for the GT2 10.1. ...
  8. I figured as much. I saw a youtube tutorial on...

    I figured as much. I saw a youtube tutorial on how to make a macro with tasker to simulate navigating to the navigation settings and clicking on/off when a certain app is used. I may do that for my...
  9. Gib, have you dealt with turning off GPS with...

    Gib,
    have you dealt with turning off GPS with tasker? I've tried but it just won't turn it off. My GT is rooted and has secure settings with helper installed (gives tasker access to events not...
  10. Thanks Gib; most of it has been pretty...

    Thanks Gib; most of it has been pretty painless...until I got to the point of actually installing it. You might have even more of a difficult time since you probably still have the metal bracket...
  11. Thanks Scott! This weekend I made the mounting...

    Thanks Scott!

    This weekend I made the mounting bracket and installed the GT + Faceplate in the Jeep. It was a struggle but I managed to get through that phase. First off, I ran into some major...
  12. Thanks Gibb! I should have it in the jeep this...

    Thanks Gibb! I should have it in the jeep this weekend. I'll have to run a temporary power to it because my stuff from Amazon hasn't made it in yet.
  13. I would need at least 2 to 3 inches of throw. ...

    I would need at least 2 to 3 inches of throw. Only because my center console has a seperator on both sided (see pic a few posts up) that sticks out about 2 inches. I would have to clear this in...
  14. I just had an idea. What if I built a small...

    I just had an idea. What if I built a small electromagnet and attached this rare earth magnet to the back of the cradle. I could had an on/off push button to the electromagnet so when it has power...
  15. Thanks for the tips Scott. It's good to bounce...

    Thanks for the tips Scott. It's good to bounce ideas around so you can get different options. As far as the relay, I don't even think you need one if you're going to use a double pole, double...
  16. Thanks Scott. I was referring to fiberglassing...

    Thanks Scott. I was referring to fiberglassing the bezel and dock at the same time. I got past that checkpoint using a little bit of your ideas. I added my worklog to my signature. Good luck and...
  17. I'll have to try that app out. PlayerPro has a...

    I'll have to try that app out. PlayerPro has a EQ plug-in that pretty nice but is limited on gesture control. I think it will only fwd to next track or previous track. Nice Avatar by the way! I...
  18. It would be easier if it dropped in from the top...

    It would be easier if it dropped in from the top but because the charging port is on the left side (when the tablet is in landscape position) I'll have to slide it in from the right. I chose this...
  19. got the excess fiberglass cut out and did a test...

    got the excess fiberglass cut out and did a test fit with the cradle and tablet. Like a glove!
    66631


    66632


    First coat of filler; sanded with 60 grit
    66633
  20. My plan is to have it overlap somewhat at the...

    My plan is to have it overlap somewhat at the bottom near the airducts. Since it's prett far back there you should really see where it overlaps. I'll have to cut the back of the bottom to make up...
  21. Alright! Got two layers of fiberglass on. Now...

    Alright! Got two layers of fiberglass on. Now it's time to wait. I'll cut the excess off later this afternoon and work from there.

    Wood guides taken out.
    66626


    First layer
    66627
  22. I thought about something similar to that when I...

    I thought about something similar to that when I first started but didn't think the tablet would slide well into it (looks like it snaps in). I think I'm going to continue on with what I have so far....
  23. no, I meant, instead of making the cradle, I...

    no, I meant, instead of making the cradle, I would use the hard case as the cradle. I would attach it in some way to the back of the trim just like I would with the cradle (with the right side cut...
  24. This is really my first time working with...

    This is really my first time working with fiberglass as well. One of the main differences between figerglass and ABS plastic is fiberglass is a little easier to work with (for novices like myself). ...
  25. I know right? Every time someone new got in my...

    I know right? Every time someone new got in my Jeep they would ask me if that was a gun case. It would be a cool place to have one.
Results 1 to 25 of 112
Page 1 of 5 1 2 3 4