Search:

Type: Posts; User: Aberk; Keyword(s):

Looking for on the store?
Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. If the same tool worked on an Escalade, but...

    If the same tool worked on an Escalade, but doesn't work on an M3 and you were able to get OBD data from the M3(right protocol), the BMW may have a diagnostic bus connected to a gateway that has no...
  2. Replies
    16
    Views
    8,508

    multiple cameras on single screen?

    I want to run multiple cameras on my truck and display them on the same screen side by side or one at a time. I have seen setups like these for security systems, but don't know if there is a mobile...
  3. Replies
    9
    Views
    1,344

    http://standards.sae.org/j1979_201009

    http://standards.sae.org/j1979_201009
  4. Replies
    7
    Views
    1,456

    That is the idea, yes. I have a CAN to...

    That is the idea, yes.

    I have a CAN to analog dev kit coming (http://www.phytec.com/products/can/canopen-io-nodes/peakmicromod-eval-kit.html), but the cost to reproduce it would be a bit pricey...
  5. Replies
    7
    Views
    1,456

    Time isnt really an issue and size isnt that...

    Time isnt really an issue and size isnt that important as there is a good bit of space behind my dash. Its a personal project and I'm going to try and have the thermocouple hardware and amp by the...
  6. Replies
    7
    Views
    1,456

    This is the closest thing I have found so far. I...

    This is the closest thing I have found so far. I also found the source code, but I'm looking for something already packaged.
    ...
  7. Replies
    7
    Views
    1,456

    analogue sensor to CAN?

    I want to install an EGT sensor on my truck, but I want to continue using my SCII for trans temp, oil temp and IAT and not have to install an additional gauge. I am looking for some small device...
  8. Replies
    11
    Views
    11,563

    If you want to listen to both busses at the same...

    If you want to listen to both busses at the same time you will need 2 "ELM" knockoffs at the very least. You could use one ELM and switch the speeds manually, but then you would have a HS CAN and MS...
  9. Replies
    16
    Views
    16,511

    Last time I had to install a VCP, I went to my...

    Last time I had to install a VCP, I went to my device manager and found the comport for my device. I right clicked and went to properties. Under one of the tabs in the properties was a check box to...
  10. Replies
    6
    Views
    2,570

    depends on the parameter. For OBDII defined...

    depends on the parameter. For OBDII defined parameters, like speed, the data will be at the same CANID, Mode and PID.
  11. Replies
    4
    Views
    4,085

    Be weary of 0x2F. I have found 2 vehicles so far...

    Be weary of 0x2F. I have found 2 vehicles so far that go from 0-100 decimal with no scaling instead of 0-255/255 as is defined in the spec.
  12. Replies
    5
    Views
    2,023

    If that is the case, you need to put the message...

    If that is the case, you need to put the message ID first then 22 is your mode and you will need to supply a PID.
  13. Maybe he is monitoring temp in different areas of...

    Maybe he is monitoring temp in different areas of the tires. Sidewalls vs tread.
  14. Replies
    5
    Views
    11,288

    Yes, start can be done. Some remote start...

    Yes, start can be done. Some remote start systems use CAN messages from the WCM (wireless control module) to initiate the remote start sequence. I had a windows mobile phone talking over bluetooth...
  15. Replies
    5
    Views
    551

    I am sure the system has been run with the car...

    I am sure the system has been run with the car off by accident once or twice, but it was never long enough to drain the battery so low that the car would not start the next time.

    We plan to...
  16. Replies
    5
    Views
    551

    battery won't hold a charge

    I have a demo vehicle at work with a 1000w inverter to run the computer and some peripherals and 350w 4 channel amp for audio. The power is run from the battery to a kill switch that can cut power...
  17. While it would be awesome if you shared your...

    While it would be awesome if you shared your algorithm, I don't expect you to. Would you be willing to share the data others have collected for you?
  18. Replies
    1
    Views
    1,294

    J1708 and OBDII in same vehicle

    Why would a Ford F650 have both and what would be available on each?
  19. Replies
    14
    Views
    3,970

    let's hope the knockoff is too. ;-)

    let's hope the knockoff is too. ;-)
  20. Replies
    14
    Views
    3,970

    I have seen the same thing when sending CAN250...

    I have seen the same thing when sending CAN250 messages on a CAN500 bus. It was in a SAAB 93. Is your ELM like device auto detecting the protocol and sending CAN250 messages before it find the...
  21. From the J1939 Spec... "The 11 bit identifier...

    From the J1939 Spec...

    "The 11 bit identifier definition is not directly a part of J1939 but is included to assure that users of it can coexist on the same network without conflict. J1939 will not...
  22. Replies
    121
    Views
    113,065

    Your Honda likely uses a MAP (manifold absolute...

    Your Honda likely uses a MAP (manifold absolute pressure) sensor. This sensor data is located at mode 0x01 PID 0x0B. There have been equations posted to this site that will show you how to compute...
  23. Replies
    10
    Views
    3,325

    J1708 isn't CAN, but they used the J1850 pins. ...

    J1708 isn't CAN, but they used the J1850 pins. Which, ironically, are the same pins that are driven by our product for J1708. I.E. our device can be configured for heavyduty or OBDII and the same...
  24. Replies
    10
    Views
    3,325

    I have encountered connectors like this in some...

    I have encountered connectors like this in some heavy duty Chevy trucks that are actually J1708 in a J1962 connector. That took awhile to figure out.
  25. Thread: Help with cables

    by Aberk
    Replies
    9
    Views
    1,704

    I am pretty sure the ELM wont work with OBDI, but...

    I am pretty sure the ELM wont work with OBDI, but maybe some one else will chime in and say differently.
Results 1 to 25 of 99
Page 1 of 4 1 2 3 4