Search:

Type: Posts; User: digimotojoel; Keyword(s):

Looking for on the store?
Page 1 of 11 1 2 3 4

Search: Search took 0.06 seconds.

  1. Digimoto sells the mOByDic based interfaces now...

    Digimoto sells the mOByDic based interfaces now (we used to sell ELM), but the response speeds on this interface are much greater then what the ELM based interfaces can offer (albeit somewhat...
  2. Replies
    7
    Views
    5,911

    You do not need two computers to simulate serial...

    You do not need two computers to simulate serial communication between two applications. As far as an ELM emulator app is concerned, I know ScanTool.net has one, but I am not sure if they would offer...
  3. Replies
    5
    Views
    11,891

    Digimoto actually distributes mOByDic based...

    Digimoto actually distributes mOByDic based interfaces that are manufactured by this company and they are good looking little units, high quality. I would recommend them as a Bluetooth option, but I...
  4. Replies
    5
    Views
    11,891

    the elmscan 327 is the elmscan 5, if you are...

    the elmscan 327 is the elmscan 5, if you are looking for an elm 327 bluetooth interface check out: http://www.vitalengineering.co.uk/ .
  5. Replies
    6
    Views
    1,942

    I strongly suggest any licensed users of our 4.03...

    I strongly suggest any licensed users of our 4.03 software upgrade to 5.0. There are many enhancements and new features ~ it is a completely re-write and is a free upgrade to existing customers.
  6. Replies
    2
    Views
    2,734

    ScanTool.net offers an open source version of...

    ScanTool.net offers an open source version of their application which you could use as a template for your design if you wish (there are other applications available that are open source as well)....
  7. My bad, I must have skipped a response there, it...

    My bad, I must have skipped a response there, it doesn't look like there is a compatibility issue at all.
  8. The OBD-Diag hardware does communicate a little...

    The OBD-Diag hardware does communicate a little differently (so I would imagine their software does too). We have some of their hardware in house we have been looking at to integrate with Digimoto...
  9. Replies
    48
    Views
    2,443

    In the twin cities we have Mall of America... and...

    In the twin cities we have Mall of America... and I believe the entire city of Detroit could fit inside of it.
  10. If you are using the ELM it's not going to matter...

    If you are using the ELM it's not going to matter what app you are using, you are going to see slow refresh rates. What front end were you looking to tie an OBDII solution into? A couple of the good...
  11. The fact is mp3car.com is probably worth over 2...

    The fact is mp3car.com is probably worth over 2 million dollars to mp3car.com itself. It is their entire business and without it they would lose virtually all revenue (outside of any money they may...
  12. Replies
    3
    Views
    6,333

    Updated rev 19 and 21.

    Updated rev 19 and 21.
  13. The interface Digimoto sells is a single unit as...

    The interface Digimoto sells is a single unit as well.
  14. Replies
    3
    Views
    6,628

    We are planning on releasing a "lite" version of...

    We are planning on releasing a "lite" version of Digimoto 5.0, but will not come until our 5.0 release. If you can wait a couple weeks you'll be able to use our trial software and then decide if it...
  15. StreetDeck as well.

    StreetDeck as well.
  16. You will see about the same rate you see on our...

    You will see about the same rate you see on our regular mOByDic packages right now (on average about 17-18 updates a second) on non CAN based vehicles and well over a 100 updates a second on CAN...
  17. Replies
    6
    Views
    1,942

    Here's a post I made a couple weeks ago, someone...

    Here's a post I made a couple weeks ago, someone had asked a similar question. Hopefully this gives anyone looking for a solution a little more info on what is out there and what their options are:
    ...
  18. Replies
    16
    Views
    9,003

    H= elm327 v1.1 T= ATSPO E H= ? T= 0100 E H=...

    H= elm327 v1.1
    T= ATSPO E
    H= ?
    T= 0100 E
    H= searching...... unable to connect

    You received a ? response because it did not understand what you were trying to do. Type AT SP 0 (zero, not an O)...
  19. Replies
    3
    Views
    1,694

    Check out these ELM single protocol interfaces on...

    Check out these ELM single protocol interfaces on eBay:
    ...
  20. Replies
    16
    Views
    9,003

    That's a good thought Paul. However, the docs...

    That's a good thought Paul. However, the docs state that if the chip attempted to connect to a protocol other then the currently defaulted protocol (if not on automatic search) it would reply with a...
  21. Replies
    16
    Views
    9,003

    http://www.scantool.net/forum/index.php?board=1;to...

    http://www.scantool.net/forum/index.php?board=1;topic=2175.2#msg8415

    I found a post here where you state that the response is "UNABLE TO CONNECT". You have to realize when you are looking for help...
  22. Replies
    16
    Views
    9,003

    That is very interesting and appears to be an...

    That is very interesting and appears to be an error within the ELM. I have looked over the ELM327 spec and see no mention of that response even being possible (It is interesting to me that you...
  23. Replies
    7
    Views
    7,241

    The parameter lists are really meaningless...

    The parameter lists are really meaningless without the PIDs associated with the parameters. Without the identification codes you can not retrieve the sensor values.
  24. Replies
    16
    Views
    9,003

    Using the 323 chip only 9600 baud was possible....

    Using the 323 chip only 9600 baud was possible. Baud rate on the ELM should have no affect on communication. If you can talk to one vehicle, you should be able to talk to second vehicle with the same...
  25. Replies
    16
    Views
    9,003

    What responses are you getting from the ELM on...

    What responses are you getting from the ELM on the commands you are entering through hyperterminal? If you post a sample session, might be able to help you out more.
Results 1 to 25 of 265
Page 1 of 11 1 2 3 4