Search:

Type: Posts; User: AWehmeyer; Keyword(s):

Looking for on the store?
Page 1 of 2 1 2

Search: Search took 0.04 seconds.

  1. I've worked in consumer electronics for nearly 25...

    I've worked in consumer electronics for nearly 25 years in a retail store and for a major manufacturer of audio equipment. Everything is about customer service--from the definition of products, their...
  2. Replies
    15
    Views
    2,521

    Sounds like the pulse is too long. I use a 2140,...

    Sounds like the pulse is too long. I use a 2140, and that seems to be adjustable.
  3. I have this problem too...or a similar one. I...

    I have this problem too...or a similar one. I found that by delaying the power to the screen for 30 seconds it's fixed. The time may be different for different systms, though.
  4. Replies
    24
    Views
    5,258

    Try TC Electronics or RME. They're both pretty...

    Try TC Electronics or RME. They're both pretty expensive, but the Konnekt48 includes a remote with a volume control. That's what I chose.
  5. Replies
    22
    Views
    2,141

    It doesn't work that way. You can change the...

    It doesn't work that way. You can change the amount of power that the amplifier makes by adding resistance either in series or in parallel. If you put a resistor in parallel with the speaker, the...
  6. Replies
    22
    Views
    2,141

    http://www.jblpro.com/pub/technote/spkpwfaq.pdf ...

    http://www.jblpro.com/pub/technote/spkpwfaq.pdf

    http://www.jblpro.com/pub/technote/lowpower.pdf

    Check out these two links for a better understanding of power handling.
  7. Replies
    16
    Views
    4,278

    Despite what everyone else says and what you've...

    Despite what everyone else says and what you've probably read, the 4 gauge wire is definitely overkill. Unless you're dying to spend a fortune on power hookup, there are much cheaper ways to do that....
  8. Never ground to the car's frame--if it's a car...

    Never ground to the car's frame--if it's a car that has a frame. IN all cases, the sheetmetal is the best place, and this is where the alternator is grounded. THe body (in a car that has a frame) is...
  9. Replies
    4
    Views
    1,636

    Is the laptop running on its battery when you...

    Is the laptop running on its battery when you experience the whining? If you have a power supply connected to the car, disconnect it and see if the noise is only present when the laptop is powered by...
  10. I can't imagine any "excessive high frequency...

    I can't imagine any "excessive high frequency losses". Anyway, put the transformers near the amps. The length of the input cables won't matter.
  11. It's just a simple transformer--like the ones...

    It's just a simple transformer--like the ones that should be inside that GLI. If you want to spend a fortune, you can go for these: http://www.jensen-transformers.com/datashts/ci2rr.pdf

    Just...
  12. The TIO is an amplifier, not a preamplifier....

    The TIO is an amplifier, not a preamplifier. Check to see if the TIO's output negative connection is continuous to chassis ground or if it's not connected directly, how much resistance is there...
  13. Replies
    4
    Views
    1,636

    Ground loop isolators aren't a band-aid. Good...

    Ground loop isolators aren't a band-aid. Good ones include a prettyhigh-quality transformer that just reflects the inpedance of the next component rather than connecting directly to it. Buy a good...
  14. Replies
    70
    Views
    35,443

    Actually, if you mess around with the sensitivity...

    Actually, if you mess around with the sensitivity adjustment, the dead zones and the min/max settings, it's pretty easy to isolate the movement and be sure that moving the control in one axis doesn't...
  15. Wow. that's helpful...and I just bought a $1500...

    Wow. that's helpful...and I just bought a $1500 soundcard because I couldn't figure that out...Oh well... :)
  16. Replies
    16
    Views
    4,340

    JJ, First, Nominal impedance isn't a measured...

    JJ,
    First, Nominal impedance isn't a measured parameter, it's a name. Of course, the impedance of a speaker is frequency dependent and the big rise at resonance is a result of back EMF from the coil...
  17. Replies
    16
    Views
    4,340

    No, they're still 2-ohm speakers and they sound...

    No, they're still 2-ohm speakers and they sound MUCH better than last year's Kappa.
  18. Replies
    4
    Views
    1,011

    That depends on what the tweeter faceplate is...

    That depends on what the tweeter faceplate is designed to do. If it's simply protection from fingers, changing it won't be a problem. If the faceplate includes a small disc placed very close to the...
  19. Replies
    14
    Views
    1,324

    In fact, many amplifiers include differential...

    In fact, many amplifiers include differential inputs and a high-level signal can be used on the RCA inputs. The input sensitivity control will have to be turned down, though.

    Here's how to tell if...
  20. We stand behind these speakers 100%. As I wrote...

    We stand behind these speakers 100%. As I wrote earlier, we've never had a radio fail driving these speakers.
  21. Durwood, The Infinity speakers will work fine...

    Durwood,
    The Infinity speakers will work fine with all aftermarket radios. Of course, before we built these things, we tested OE radios and aftermarket radios driving them and nothing failed....
  22. Too Long in Exile--Van Morrison River--The Joni...

    Too Long in Exile--Van Morrison
    River--The Joni Letters-- Herbie Hancock
    Hope--Hugh Masekela
    Before These Crowded Streets--Dave Matthews Band
    Diana Krall--Live in Paris
    In Absentia--Porcupine...
  23. If you've installed a bunch of damping material...

    If you've installed a bunch of damping material in the doors already, modeling clay isn't going to help.

    Try this:

    Disconnect the subwoofer and listen only to the front speakers. If the...
  24. There's no need to run new wires to any speakers....

    There's no need to run new wires to any speakers. It isn't worth the hassle. Also, with speaker wires there's almost ne need to be concerned about the placement of the wires.
  25. Replies
    414
    Views
    81,895

    I found the dll, but the exe still won't run. I...

    I found the dll, but the exe still won't run. I get an error message indicating that the program needs to close. can anyone offer a suggestion?
Results 1 to 25 of 28
Page 1 of 2 1 2