Search:

Type: Posts; User: Altimat; Keyword(s):

Looking for on the store?
Page 1 of 20 1 2 3 4

Search: Search took 0.20 seconds.

  1. Replies
    384
    Views
    38,189

    Thats funny xmadcowx. I've been out-of-touch...

    Thats funny xmadcowx. I've been out-of-touch since about that era as well and it sounds like you are describing what I remember of current front-end technology.

    I moved from WI to Parrish, FL two...
  2. Replies
    41
    Views
    63,462

    Sticky: The non-nav panel is the one I used and it fit...

    The non-nav panel is the one I used and it fit the 7" Xenarc surprisingly well. I'm assuming you want it for the door mechanism? It is a huge amount of work to make that blend into an Altima dash...
  3. Replies
    41
    Views
    63,462

    Sticky: If I remember right the cubby is not available...

    If I remember right the cubby is not available separately. It is included with the entire center dash panel.
  4. Replies
    79
    Views
    142,301

    Sticky: ABS isn't that flexible, but I found that the...

    ABS isn't that flexible, but I found that the bond is key as much as the product. Regardless of what material you use there will be differences in flexibility and expansion rates with temperature...
  5. Replies
    79
    Views
    142,301

    Sticky: I restored cars for 20+ years quite a few of...

    I restored cars for 20+ years quite a few of which were fiberglass, and not the least of which was the Oldsmobile XP-20 concept car that set a new Barrett-Jackson auction price record a couple years...
  6. Replies
    25
    Views
    100,928

    Sticky: There are no gaps in the corners, but this was...

    There are no gaps in the corners, but this was only my first headrest screen installation. I don't believe there is any way the upholstery could have fit between the bezel and the screen.
  7. Replies
    41
    Views
    63,462

    Sticky: Yes just extend it to wherever you need it. Most...

    Yes just extend it to wherever you need it. Most RC hobby shops have the wire too. It works well.
  8. Replies
    41
    Views
    63,462

    Sticky: I haven't lengthened the ribbon cable to the...

    I haven't lengthened the ribbon cable to the button board. You may want to try Digi-Key for a longer ribbon cable of that type but I'm not sure that it will be available. You could always relocate...
  9. Replies
    9
    Views
    2,526

    Poll: Epoxy sticks best to a properly prepared surface....

    Epoxy sticks best to a properly prepared surface. Use glass or carbon cloth with it for strength. Mix it with microballoons to make a filler.
  10. Replies
    2
    Views
    1,146

    You have to thoroughly sand EVERYWHERE any...

    You have to thoroughly sand EVERYWHERE any adhesive, primer, paint, etc. is going to be applied.
  11. Replies
    79
    Views
    142,301

    Sticky: Your best bet it to get your paint products...

    Your best bet it to get your paint products wherever you found the Evercoat. The commercial paints like SEM are way better than the consumer paints at auo parts, hardware, and home stores.
  12. Replies
    13
    Views
    3,628

    And to create adhesion. What is the red frosting...

    And to create adhesion. What is the red frosting all over the top? I hope that isn't the hardener???
  13. Replies
    14
    Views
    1,762

    I don't mind the buttons in general, but the...

    I don't mind the buttons in general, but the goofy size, shape, and configuration is what doesn't look right after the screen is moded into an otherwise rectangular dash setup. The Xenarc is much...
  14. Replies
    14
    Views
    1,762

    Desolder it from the board and use 3-conductor RC...

    Desolder it from the board and use 3-conductor RC servo ribbon cable to extend it.
  15. Replies
    79
    Views
    142,301

    Sticky: You can disassemble the Lilli. Just remove...

    You can disassemble the Lilli. Just remove everything from the back of the front bezel but do not mess with the LCD ribbons.

    The bare woodgrain does need to be sealed either with a layer of filler...
  16. Replies
    16
    Views
    3,793

    In that case you may get away with respraying...

    In that case you may get away with respraying just those parts. I'd sand off the wrinkled paint instead of using a solvent. If you use a solvent it will soak into the base layers and you'll have to...
  17. Replies
    16
    Views
    3,793

    Usually this is caused by some incompatibilty...

    Usually this is caused by some incompatibilty between the primer and paint. Laquer-based products over enamel-based products is the most common cause. Enamel over lacquer is fine. If you use SEM...
  18. Replies
    25
    Views
    15,827

    What IMs?

    What IMs?
  19. Yes the box was awesome I saved mine too. No rush...

    Yes the box was awesome I saved mine too. No rush take your time. It will be sitting here for months anyway. House isn't even framed yet! :)
  20. Had to buy it for a friend's new house. Thanks...

    Had to buy it for a friend's new house. Thanks Chris! Hope you have the original box. :)
  21. Replies
    125
    Views
    9,569

    No kidding? I think some of the cars suggested...

    No kidding? I think some of the cars suggested above are far uglier. With the exception of the Titan of course. :)

    http://www.autoblog.com/entry/1234000290066700/
  22. Replies
    125
    Views
    9,569

    You can use my Altima. :) How about the new...

    You can use my Altima. :) How about the new Eclipse?
  23. Replies
    23
    Views
    3,811

    A few always get past me and are not filled with...

    A few always get past me and are not filled with the primer. I fill them in with a small pointed brush and some primer after the last coat is sprayed.
  24. Replies
    3
    Views
    3,245

    Adapting another suitable OEM part is the best...

    Adapting another suitable OEM part is the best way to do this sort of thing IMO.
  25. Replies
    7
    Views
    4,778

    The host of the picture above does not allow...

    The host of the picture above does not allow linking from other sites. Paste this into your address bar:

    http://pics.bbzzdd.com/users/nboy22/small.JPG
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4