Search:

Type: Posts; User: heavymetals; Keyword(s):

Looking for on the store?
Page 1 of 6 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6
    Views
    1,545

    OP was asking whats available.

    OP was asking whats available.
  2. Replies
    6
    Views
    1,545

    Check these offerings: http://www.chasecam.com

    Check these offerings:

    http://www.chasecam.com
  3. Replies
    71
    Views
    14,523

    You can email me, PM sent. Thanks for the...

    You can email me, PM sent.

    Thanks for the comps and interest.
  4. Replies
    71
    Views
    14,523

    Composite sync is the same as combined sync, but...

    Composite sync is the same as combined sync, but you will not be able to get the high resolution (600X800 and higher) using composite sync.
  5. Replies
    2
    Views
    1,405

    check the last page of my project. Burr Brown...

    check the last page of my project.

    Burr Brown makes a chip that does it.

    Analog Device makes a chip that goes the other way

    http://www.analog.com/en/circuits-from-the-lab/CN0040/vc.html
  6. Replies
    71
    Views
    14,523

    Got a picture on the OEM display, now just have...

    Got a picture on the OEM display, now just have to get it to sync.

    Goal is a NTSC back up camera input.
  7. Replies
    71
    Views
    14,523

    New update. Revisited the OEM display and...

    New update.

    Revisited the OEM display and tried some new modifications:

    Will either have good or bad news after testing.
  8. Check this: ...

    Check this:

    http://www.ebay.com/itm/Component-YPbPr-RGB-RCA-to-Composite-Yellow-RCA-and-S-Video-w-Down-Scaler-/130711442135?pt=US_Video_Cables_Adapters&hash=item1e6f0252d7
  9. Replies
    71
    Views
    14,523

    Here is the interface. 2 ICs, 4 caps, 6...

    Here is the interface.

    2 ICs, 4 caps, 6 resistors.
  10. Replies
    71
    Views
    14,523

    UPDATE: I had to get two switching power...

    UPDATE:

    I had to get two switching power supplies that put out 15 volts (adjustable) so I could supply the positive and negative rails for the chip to work.

    Then I found software that actually...
  11. You might try using copper tape and solder a...

    You might try using copper tape and solder a drain wire from the copper to ground (Farady shield)

    You might also try "desensitizing" the VGA lines by loading them with a resistor to ground.
  12. Replies
    71
    Views
    14,523

    UPDATE: Grabbed the audio feed from the radio...

    UPDATE:

    Grabbed the audio feed from the radio and it is differential.

    Found a chip that will convert from differential to single ended and it works great.

    Now the problem is volume control...
  13. Replies
    71
    Views
    14,523

    UPDATE: Interfacing the OEM radio/nav to the...

    UPDATE:

    Interfacing the OEM radio/nav to the 5.1 sound is the new project.

    Tried using LOC's and the distortion from the transformers is too much to bare.

    Going to use a differential to...
  14. Replies
    71
    Views
    14,523

    Just a 5 volt regulator LM series. Mint box is...

    Just a 5 volt regulator LM series.

    Mint box is the heat sink and mounted to the amplifier heat sink, no worries at all.
  15. Replies
    6
    Views
    1,170

    I see a mason jar full of moonshine? Looks ESD...

    I see a mason jar full of moonshine?

    Looks ESD safe. hahaha
  16. You bet I did. Check it out: ...

    You bet I did.

    Check it out:

    http://www.mp3car.com/worklogs/153699-a-macd-v.html
  17. Replies
    13
    Views
    3,791

    I figured this would be more technical discussion...

    I figured this would be more technical discussion rather then a personal taste discussion.

    The OP asked how to do it, rather then opinions of 5.1 (as I read it).
  18. Replies
    13
    Views
    3,791

    To the OP. Forget what the naysayers spout off...

    To the OP.

    Forget what the naysayers spout off with.

    IT IS WORTH IT.

    A lot of my music sounds so much more defined with the 5.1.
  19. Replies
    13
    Views
    3,791

    I installed a 5.1 decoder and power supply in my...

    I installed a 5.1 decoder and power supply in my setup.
  20. I believe EFI live can do and also HP tune. ...

    I believe EFI live can do and also HP tune.

    You will not be able to remap (that I have heard of ) to an external trim.

    You would have to have the entire "tune" being controlled by the OBD port,...
  21. Look at using one of the above and a USB...

    Look at using one of the above and a USB bluetooth adapter.

    I would suggest you get off the idea of OBD/CANBUS unless you are gonna spend some time getting educated in what they are for and the...
  22. Forget using a conventional ECU/PCM and adapting...

    Forget using a conventional ECU/PCM and adapting it.

    You need a multiple analog input data logger.

    http://www.ni.com/data_logger/multichannel.htm
    ...
  23. Replies
    7
    Views
    1,127

    The only way I know is to monitor the OBD...

    The only way I know is to monitor the OBD continually with a code scanner.

    They are pretty cheap, but I would look into a spare PCM as they are pretty cheap also.
    ...
  24. Replies
    48
    Views
    2,866

    Thought so.

    Thought so.
  25. Replies
    7
    Views
    1,127

    I thought he said he put an OBD scanner to get...

    I thought he said he put an OBD scanner to get codes so I assume it was check engine light related and that was his problem.

    If not, generate a known code.

    Disconnect a spark plug wire and that...
Results 1 to 25 of 141
Page 1 of 6 1 2 3 4