Page 2 of 45 FirstFirst 123456789101112 ... LastLast
Results 11 to 20 of 442
Like Tree1Likes

Thread: 1998 Camaro Install- lots of pics, rear seat delete

  1. #11
    Constant Bitrate
    Join Date
    Apr 2007
    Posts
    134
    lol, i've got too many subs as is

    4 - 10" L7's
    3 - 10" Type R's
    2 - 12" MTX Thunder6000s
    1 - 12" Audiobahn AWIS12... immortal series


    But yeaaa... i haven't touched the 12s in like a year or so.. they're my olddd subs, i never even powered on the Audiobahn one... quad 2ohm 2000w RMS plus it was audiobahn... i was in an audiobahn stage and sorta... yeaa... jumped the gun and bought that sub, i didn't want to fry my amps with a crappy sub but it IS intriguing... the sub weighs around 65 lbs and has 4 2ohm terminals

  2. #12
    Maximum Bitrate sporty_drew's Avatar
    Join Date
    Mar 2006
    Location
    Iowa
    Posts
    662
    lol, pm me the specs on the L7's i might ponder them instead...
    1998 Camaro Worklog Starting over, New setup for 2010

  3. #13
    Constant Bitrate
    Join Date
    Apr 2007
    Posts
    134
    good god, are you ALWAYS online?! lol, okay okay, PM'ing yah now

  4. #14
    Low Bitrate Super_dave's Avatar
    Join Date
    Sep 2006
    Posts
    107
    Nice Job on the faceplate ext , here's mine
    Attached Images Attached Images   

  5. #15
    Maximum Bitrate sporty_drew's Avatar
    Join Date
    Mar 2006
    Location
    Iowa
    Posts
    662
    Quote Originally Posted by Super_dave View Post
    Nice Job on the faceplate ext , here's mine
    Very nice, I'm glad someone who did this actually ended up using it lol. That looks very clean.

    Here is what i received in the mail today


    I didn't have the cover plate on the one side when i took the pics because i had just finished installing and setting it. It's set at 80 for the lp filter and at 38.7 v at 2 ohms
    1998 Camaro Worklog Starting over, New setup for 2010

  6. #16
    Maximum Bitrate sporty_drew's Avatar
    Join Date
    Mar 2006
    Location
    Iowa
    Posts
    662
    I just received my Lilliput 619, I'll get pictures of it in the bezel when i get it in. luckily the Lilliput fit in where i had my lcd with only mild filing to the opening
    It didn't come with the bezel for the front or the rca input cable(I'll be ordering the cable this week)
    1998 Camaro Worklog Starting over, New setup for 2010

  7. #17
    Maximum Bitrate sporty_drew's Avatar
    Join Date
    Mar 2006
    Location
    Iowa
    Posts
    662

    Monitor in Bezel

    Well i ordered my M2-ATX today and it should be here on Wednesday
    I'm thinking i'm going to be changing up my motherboard choice yet again and am going to be using a 2.4 ghz celeron with 512 ram and 96mb onboard video. It takes about the same amount of power as my 1.8 ghz P4 if not a bit less. I will be ordering a second m2 or m1 for the usb devices, hard drive, dvd burner, and monitor as i add them to the carputer. for now the m2 will power the motherboard and hard drive. Well onto the pictures of my monitor in the bezel before final primer and then paint, i will hopefully be getting around to this tomorrow but i might work on the skin a bit more. (sorry for the bad pics)

    1998 Camaro Worklog Starting over, New setup for 2010

  8. #18
    Maximum Bitrate sporty_drew's Avatar
    Join Date
    Mar 2006
    Location
    Iowa
    Posts
    662
    I just painted the monitor I'm not sure if i like the grey it came out to be. It's plastic textured paint but it has a little shimmer (looks like a lot in the pictures) I'm going to have to wait for it to dry so i can take it out and put it in the camaro and see what it looks like. anyways here are the pictures of it just after paint





    I hope someone is actually looking (enjoying ? ) the pictures of progress...
    1998 Camaro Worklog Starting over, New setup for 2010

  9. #19
    Maximum Bitrate sporty_drew's Avatar
    Join Date
    Mar 2006
    Location
    Iowa
    Posts
    662

    Bezel with monitor/ bezel in car

    I put my monitor in there for a test fit when i got out of school and everything looks good.




    I also put the bezel in the car to see how it matched up and surprisingly it is very close, remember it isn't matching the light gray behind it but the gray around the inside of the gauges and around the shifter where the cigarette lighter is, but not around the cup holder to the right of the cigarette lighter.



    That was my best picture due to the glare and they never look the same color as in person, but I'll get more of it when the monitor is in. I also plan on repainting the other pieces that it is suppose to be matching because i like the little "shimmer".
    1998 Camaro Worklog Starting over, New setup for 2010

  10. #20
    Maximum Bitrate sporty_drew's Avatar
    Join Date
    Mar 2006
    Location
    Iowa
    Posts
    662
    Oh Yea!!! I'm in the camaro now and everything is running great. I'll post pics later tonight and post up problems i ran into along the way (not many tho)
    1998 Camaro Worklog Starting over, New setup for 2010

Similar Threads

  1. 2002 Camaro Install
    By Z28CTYHNTR in forum Show off your project
    Replies: 31
    Last Post: 12-19-2006, 03:56 PM
  2. I want to install a switch
    By Froogle in forum Power Supplies
    Replies: 28
    Last Post: 04-13-2006, 10:12 PM
  3. 78 Camaro Type LT install.
    By hcker2000 in forum Show off your project
    Replies: 10
    Last Post: 12-31-2005, 07:29 PM
  4. 1998 Honda CRV Headunit-less install
    By hihidamon in forum Show off your project
    Replies: 7
    Last Post: 02-24-2005, 04:38 PM
  5. Please help install a Front End
    By Zebelkhan in forum Newbie
    Replies: 5
    Last Post: 01-31-2005, 05:40 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •