http://www.mp3car.com/vbulletin/ Forum designated for the Fusion Brain controller. en Sat, 21 Nov 2009 11:55:29 GMT vBulletin 60 http://www.mp3car.com/vbulletin/images/misc/rss.jpg http://www.mp3car.com/vbulletin/ http://www.mp3car.com/vbulletin/fusion-brain/137180-problems-maping-momentary-button-rrfusion.html Tue, 10 Nov 2009 16:47:04 GMT im trying to map a rrfusion command into the keyTBL.ini but all variations i have tried so far wont work.

toggle buttons work fine with this command:

key#,"DIGITALOUT0;TOGGLE",

however momentary buttons wont work

key# ,"DIGITALOUT0;RELEASE &DIGITALOUT2;HOLD& "

i hope someone can help me out with the right syntax, format here...
thx! ]]> Fusion Brain sgtpepperaut http://www.mp3car.com/vbulletin/fusion-brain/137180-problems-maping-momentary-button-rrfusion.html http://www.mp3car.com/vbulletin/fusion-brain/137135-launch-external-program.html Sun, 08 Nov 2009 22:56:04 GMT I can't see that this question has not been asked yet, but after searching and searching I have not come up with anything.

Basically I want to use a AUX out on my cars alarm/remote start to boot up my PC, and then when the computer is on and it loads FCC I want my brain to sense that the line from the alarm is active and from there launch a batch file i have that will activate my wifi card. I know how to do all the wiring and how it will all work. My question is, is there a command line in the logic that you can launch an external program? I have all the logic to get to that point squared away, but don't know about a "run" command. Example: "run c:\wifi_on.bat" or something along those lines. ]]> Fusion Brain bratnetwork http://www.mp3car.com/vbulletin/fusion-brain/137135-launch-external-program.html http://www.mp3car.com/vbulletin/fusion-brain/137054-fusion-outputs-hibernate-resume.html Wed, 04 Nov 2009 22:40:24 GMT I'm using 1 output to control a relay that powers my amps remote wires.

I have the default of the output to off

I'm using the ExecTBL.ini of RR to send commands:
"ONRESUME","fusion_vote_AmpON"

This command works A-OK, only problem is when coming back from hibernate the fusion brain restores the last state of the output (on) before my PC is ready (and before AmpON gets called) and I get a big screech and thump. It works fine if I manually turn off the output before hibernating.

I try using this command:
"ONSUSPEND","fusion_vote_AmpOFF"
but it throws an error.


Any ideas or input from anyone would be much appreciated! ]]> Fusion Brain JiC http://www.mp3car.com/vbulletin/fusion-brain/137054-fusion-outputs-hibernate-resume.html http://www.mp3car.com/vbulletin/fusion-brain/136325-help-me-troubleshoot-my-fusion-brain.html Sat, 10 Oct 2009 16:47:48 GMT Seems like every time I try to install my fusion brain on a new computer I always have some sort of problem with Ride Runner and RRfusion. Currently I have the fusion brain set up with my laptop and when I tried to copy everything over to my carpc once again it doesn’t work. The fusion brain... Seems like every time I try to install my fusion brain on a new computer I always have some sort of problem with Ride Runner and RRfusion. Currently I have the fusion brain set up with my laptop and when I tried to copy everything over to my carpc once again it doesn’t work. The fusion brain software sees the fusion brain and it is “working properly” in the device manager.

I am using the same version Ride Runner and RRfusion in my car pc as I was in my laptop. So why is the fusion not working with ride runner?? Any ideas?

Thanks!! ]]> Fusion Brain djurchicprelude http://www.mp3car.com/vbulletin/fusion-brain/136325-help-me-troubleshoot-my-fusion-brain.html