Page 8 of 10 FirstFirst 12345678910 LastLast
Results 71 to 80 of 95

Thread: 2000 chevy truck Install

  1. #71
    Low Bitrate slinkytoy's Avatar
    Join Date
    Mar 2007
    Location
    Colorado
    Posts
    97
    Front Horns are being installed in the AM. Yea baby. Here is a link to what we are installing.
    http://www.imagedynamicsusa.com/prod...=cd2&type=horn

    Very sexay

  2. #72
    Constant Bitrate
    Join Date
    Sep 2004
    Location
    Springfield VA
    Posts
    123
    how come we haven't seen any pics of everything finally installed?

  3. #73
    Newbie copter's Avatar
    Join Date
    Dec 2007
    Location
    Nor★Cal
    Posts
    55
    Quote Originally Posted by slinkytoy View Post
    Front Horns are being installed in the AM. Yea baby. Here is a link to what we are installing.
    http://www.imagedynamicsusa.com/prod...=cd2&type=horn

    Very sexay
    How and where are you mounting the horns? Have you seen http://www.usdaudio.com/sw/cars/ctruck1/ ?
    _____________________________
    06 BLACKTIE LBZ | GRAYSTONE METALLIC | MBRP 4" | AMP STEPS | KMC DIESELS | TOYO M/T'S | NCT/COGNITO 4-6" | BILSTEIN 5100'S | MAG-HYTEC DIFF COVER | HID'S | PPE XCELLERTOR |
    ______________________________________

  4. #74
    Low Bitrate slinkytoy's Avatar
    Join Date
    Mar 2007
    Location
    Colorado
    Posts
    97

    Horns are installed

    OMG!!!!!!!!!!We have front sound stage and horns are installed. Pix will follow on the installation on them. Very clean sound i was pleasently surprised in the sound.
    tonkadawg-----Here is a few pix on the center console done. I didn't have my camera today but i will post pic in the next few days of the horns.
    copter-----------Yea my horns are in the same place at one point during the install we were thinking about mounting the horns up in front by the front windshield. But moving the air vents and the sound would have rolled off the window and it just wasen't going to work. Here are a few pix for everyone to check out.
    Attached Images Attached Images         

  5. #75
    Low Bitrate slinkytoy's Avatar
    Join Date
    Mar 2007
    Location
    Colorado
    Posts
    97
    Oh yea here is the OMG wiring picture.
    Attached Images Attached Images  

  6. #76
    Low Bitrate slinkytoy's Avatar
    Join Date
    Mar 2007
    Location
    Colorado
    Posts
    97
    Picture of the 10 inch sub that is in the floor.
    Attached Images Attached Images  

  7. #77
    Newbie
    Join Date
    Apr 2007
    Location
    Glendale, AZ
    Posts
    15
    Jealous

  8. #78
    Newbie groundpounder's Avatar
    Join Date
    May 2007
    Location
    Aurora, Colorado
    Posts
    19
    Quote Originally Posted by copter View Post
    How and where are you mounting the horns? Have you seen http://www.usdaudio.com/sw/cars/ctruck1/ ?

    Copter,

    USD Audio did well with their prducts in the early and mid 90's unfortunately I don't think they "advanced with the times" Eric Stevens @ Image is continously working to improve the performance of thier HLCD's new materials for the horns molds to improving the drivers year after year.

    The ID horns are also a bit more user and install freindly.


    There is still plenty of work to be done we have to fab up the amp rack trim panels and cover/trim panels for the Cap and floor sub as wells as new rear door panels.

    Not to mention the hours of tuning tat still need to be done.
    Mile High Sound Designs
    "Fabricators of personality"
    www.mhsound.com
    Mile High Club
    Certified IASCA Judge
    IASCA Competitor
    Team Image Dynamics
    Team Arc Audio

    The Mile High Club Forums

  9. #79
    Low Bitrate slinkytoy's Avatar
    Join Date
    Mar 2007
    Location
    Colorado
    Posts
    97
    Took a road trip today about 700 miles about 10 hours. The system with the carnexit and a DSATX work great. Only one little thing happen the carnexit got a little hot and went into standby mode. I pulled over and got gas chilled for a few and started the truck back up and the power supply came back up and work for the rest of the trip no problems. Very happy with both of these power supplys. I'm running the computer on the DSATX and I'm hammering the carnexit. I'm running 1 10.4 and a 8 inch monitor. A DVD and a powered 7 port usb switch all on that carnexit and its just fine. After 6 hours and the worst thing that could happen is standby mode for a few untill it cools off a little hell i can handle that.

  10. #80
    Newbie copter's Avatar
    Join Date
    Dec 2007
    Location
    Nor★Cal
    Posts
    55
    Quote Originally Posted by groundpounder View Post
    Copter,

    USD Audio did well with their prducts in the early and mid 90's unfortunately I don't think they "advanced with the times" Eric Stevens @ Image is continously working to improve the performance of thier HLCD's new materials for the horns molds to improving the drivers year after year.

    The ID horns are also a bit more user and install freindly.
    Ya' the Holdaway's seem to have dropped off the planet. I was lucky and got to demo the Speaker Works Buick as well as Harry Kimura's Acura and a few others they built. I met Eric Stevens at a show in Ventura back in tha' day and from talking to him he pretty much copied the WaveGuide and put his own spin on it. I got to demo Eric's Sable (remember that one?) for about a half hour and we discussed mounting options for the horns. Some guys I worked with in the 80's were using EV horns in the defroster vents and talk about dynamic stage and placement. WOW!!! Eric was very interested. Remember Mark Elridge's 4Runner? He used WG's on the dash.. Anyhow so much for the trip down memory lane.
    _____________________________
    06 BLACKTIE LBZ | GRAYSTONE METALLIC | MBRP 4" | AMP STEPS | KMC DIESELS | TOYO M/T'S | NCT/COGNITO 4-6" | BILSTEIN 5100'S | MAG-HYTEC DIFF COVER | HID'S | PPE XCELLERTOR |
    ______________________________________

Similar Threads

  1. 2000 Denali Install - Lots of pics!
    By rulouder22 in forum Show off your project
    Replies: 58
    Last Post: 03-13-2007, 11:28 AM
  2. 2000 Monte Carlo SS install
    By snmnetwork in forum Show off your project
    Replies: 28
    Last Post: 04-06-2006, 01:05 AM
  3. Replies: 3
    Last Post: 02-12-2006, 07:47 PM
  4. Dash Fabrication for Chevy Truck!
    By voidunknown in forum Fabrication
    Replies: 27
    Last Post: 04-06-2005, 08:31 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •