Thread: 2003 Durango SLT / Project HiJackZX1 / 56K= D@mn this $h!+ is gonna load slow!

Originally Posted by vincenttor

i asked her are they comming again
and she said no
i found another website with cheap stuff on it but its all from china
tried on google cnbuynet reviews
but can´t find much info of it
they got cheap touchscreens , but not rooftop

http://www.cnbuynet.com/15-inch-car-...vfm-p-527.html

but dunno if its any good

ahhhhh, there was a flaw I experienced with the screen. It says VGA but it doesnt have a VGA connector. When I opened the unit, it has a small port which you connect a special cable with the VGA connector on the end. I think all the screens had this issue and most likely she got tired of having to order it from Shark. On a brighter note I found a site that sells really cheap stuff. I was looking for a stereo soundcard for my IR headphones. I am already using the onboard soundcard for phone, the PCI card for the 7.1 surround sound, and now a USB soundcard thats $6.95!!!!!!!!!!!!! Here is a link to them, they have alot of stuff, dont know if the products are any good.

http://www.buyextras.com/asusbstauso...FQkcHgod6lxNjg

PS: If you cant find a VGA roof top screen then buy the one you linked too and have a fabricator create a case that can flip down for. It will be pricey though.

I am so pi$$ed beyond imagination. Today the UPS man comes and he is delivering a package. I see a IEI box sitting on his stuff and I was like, omg, thats mine. He turns around and says no its not, its for another building. So I was like no its not, no one else orders from IEI but me, lol. So he gives it to me and I was so happy. This is were the pi$$ed part comes in, they sent me a new version of the board, which is diffrent. Headers are diffrent and worst of all there is no PCI slot, only that stupid mini PCI $h!t, that sits so far back on the MoBo that if anything goes into it, it will get in the way of the center console I just designed!!!!!!!!!!! Also i bought a SoundBlaster XtremeGamer soundcard, but in PCI form, now its useless. I mean I do see that the board is now stronger, and transistors that were then fragile are now solid. I mean but why take away something that important???????????? Do they honestly think that everyone uses mini pci? OMG, now I have to figure something out.....

Now that the rant is over, i called them and told them that i didnt understand why it did not have a PCI slot. He asked me to read off the identification number to him, which is KINO-6901-R11.... it should read KINO-690S1-R11.... He says that they accidently sent me a project board that they use for testing. He has sent me a replacement that should be here in 3 days. I swear if IEI wasnt the only one that makes this configuration of MoBo, i would have went to a new company!

OK, I realized that my console had a flaw, I made the cabin floor at a slant, but once I put the X-FI in, the slant will not allow clearance. So now I have redone it so it goes flat across and is set alittle higher. I also made the cover for the top air vent, all I need to do is cut the holes for the vents. I also need to do this for the rear of the console. Here are better pix!



Here is the view from the bottom. The little slot is were the metal case of the PC meets up with the console. This creates the seal for the air vent.



Here will be were the holes get cut for the vents.



This is the bottom back of the console, It will also get holes for vents and grills.

Originally Posted by vincenttor

good to read
and thanks for the url btw
i hope its all going well with building in your car
i was totally amazed btw for the shipping costs to nl from china

1. VIA DHL USD138.00
2. VIA UPS USD118.00
3. VIA EMS USD101.00


ouch

WHAT!!!!!!!!!!! Thats crazy.... Arent you closer to China? What were you ordering from there? Maybe its cheaper to send to someone in America, then they ship it to you?

PS: Here is the link to my front dash that Nexson Designs is doing for me, I just didnt have the skills to do it myself. He is also going to do the top of dash with the 2 custom flip up screens. JR House of Designs will be doing the upholstery for center console #2, but this time I am really going to make sure it comes out perfect.

Dodge Durango Screen Fabrication, Nexations Creations *Work Log*

Originally Posted by vincenttor

yeah dont know how much it actually costs from usa to NL
the stuff i ordered is a 15"touch screen
2 licenseplate cams and a rearview mirrorscreen machine something similair like yours
and i dont know any body in the usa so thats going to be a problem then

ur dash looks good allready btw

HAHAHAHAHA, oh god, I think ive created a "Cram as much stuff in your vehicle as possible" person. So that means you bought a Digital Quad Processor? I am having a issue with mine, it automatically defaults to this 4 way view when I turn on the car. I want to rewire the board so that when I turn on the car it automatically goes into 3 way view. I am not sure how to do this, this weekend I am going to open it up and take pictures. I am hoping some one has an idea on what areas to soder.